기압 센서

bmp280

소스: drivers/barometer/bmp280

사용법

bmp280 <command> [arguments...]
 Commands:
   start
     [-I]        Internal I2C bus(es)
     [-X]        External I2C bus(es)
     [-s]        Internal SPI bus(es)
     [-S]        External SPI bus(es)
     [-b <val>]  board-specific bus (default=all) (external SPI: n-th bus
                 (default=1))
     [-c <val>]  chip-select index (for external SPI)
                 default: 1
     [-m <val>]  SPI mode
     [-f <val>]  bus frequency in kHz
     [-q]        quiet startup (no message if no device found)
     [-a <val>]  I2C address
                 default: 118

bmp388

소스: drivers/barometer/bmp388

사용법

bmp388 <command> [arguments...]
 Commands:
   start
     [-I]        Internal I2C bus(es)
     [-X]        External I2C bus(es)
     [-s]        Internal SPI bus(es)
     [-S]        External SPI bus(es)
     [-b <val>]  board-specific bus (default=all) (external SPI: n-th bus
                 (default=1))
     [-c <val>]  chip-select index (for external SPI)
                 default: 1
     [-m <val>]  SPI mode
     [-f <val>]  bus frequency in kHz
     [-q]        quiet startup (no message if no device found)
     [-a <val>]  I2C address
                 default: 118

   stop

   status        print status info

dps310

소스: drivers/barometer/dps310

사용법

dps310 <command> [arguments...]
 Commands:
   start
     [-I]        Internal I2C bus(es)
     [-X]        External I2C bus(es)
     [-s]        Internal SPI bus(es)
     [-S]        External SPI bus(es)
     [-b <val>]  board-specific bus (default=all) (external SPI: n-th bus
                 (default=1))
     [-c <val>]  chip-select index (for external SPI)
                 default: 1
     [-m <val>]  SPI mode
     [-f <val>]  bus frequency in kHz
     [-q]        quiet startup (no message if no device found)
     [-a <val>]  I2C address
                 default: 119

   stop

   status        print status info

lps22hb

소스: drivers/barometer/lps22hb

사용법

lps22hb <command> [arguments...]
 Commands:
   start
     [-I]        Internal I2C bus(es)
     [-X]        External I2C bus(es)
     [-s]        Internal SPI bus(es)
     [-S]        External SPI bus(es)
     [-b <val>]  board-specific bus (default=all) (external SPI: n-th bus
                 (default=1))
     [-c <val>]  chip-select index (for external SPI)
                 default: 1
     [-m <val>]  SPI mode
     [-f <val>]  bus frequency in kHz
     [-q]        quiet startup (no message if no device found)

   stop

   status        print status info

lps25h

소스: drivers/barometer/lps25h

사용법

lps25h <command> [arguments...]
 Commands:
   start
     [-I]        Internal I2C bus(es)
     [-X]        External I2C bus(es)
     [-s]        Internal SPI bus(es)
     [-S]        External SPI bus(es)
     [-b <val>]  board-specific bus (default=all) (external SPI: n-th bus
                 (default=1))
     [-c <val>]  chip-select index (for external SPI)
                 default: 1
     [-m <val>]  SPI mode
     [-f <val>]  bus frequency in kHz
     [-q]        quiet startup (no message if no device found)

   stop

   status        print status info

lps33hw

소스: drivers/barometer/lps33hw

사용법

lps33hw <command> [arguments...]
 Commands:
   start
     [-I]        Internal I2C bus(es)
     [-X]        External I2C bus(es)
     [-s]        Internal SPI bus(es)
     [-S]        External SPI bus(es)
     [-b <val>]  board-specific bus (default=all) (external SPI: n-th bus
                 (default=1))
     [-c <val>]  chip-select index (for external SPI)
                 default: 1
     [-m <val>]  SPI mode
     [-f <val>]  bus frequency in kHz
     [-q]        quiet startup (no message if no device found)
     [-a <val>]  I2C address
                 default: 93
     [-k]        if initialization (probing) fails, keep retrying periodically

   stop

   status        print status info

mpl3115a2

소스: drivers/barometer/mpl3115a2

사용법

mpl3115a2 <command> [arguments...]
 Commands:
   start
     [-I]        Internal I2C bus(es)
     [-X]        External I2C bus(es)
     [-b <val>]  board-specific bus (default=all) (external SPI: n-th bus
                 (default=1))
     [-f <val>]  bus frequency in kHz
     [-q]        quiet startup (no message if no device found)
     [-a <val>]  I2C address
                 default: 96

   stop

   status        print status info

ms5611

소스: drivers/barometer/ms5611

사용법

ms5611 <command> [arguments...]
 Commands:
   start
     [-I]        Internal I2C bus(es)
     [-X]        External I2C bus(es)
     [-s]        Internal SPI bus(es)
     [-S]        External SPI bus(es)
     [-b <val>]  board-specific bus (default=all) (external SPI: n-th bus
                 (default=1))
     [-c <val>]  chip-select index (for external SPI)
                 default: 1
     [-m <val>]  SPI mode
     [-f <val>]  bus frequency in kHz
     [-q]        quiet startup (no message if no device found)
     [-T <val>]  Device type
                 values: 5607|5611, default: 5611

   stop

   status        print status info

ms5611

Source: drivers/barometer/ms5611

Usage

ms5611 <command> [arguments...]
 Commands:
   start
     [-I]        Internal I2C bus(es)
     [-X]        External I2C bus(es)
     [-s]        Internal SPI bus(es)
     [-S]        External SPI bus(es)
     [-b <val>]  board-specific bus (default=all) (external SPI: n-th bus
                 (default=1))
     [-c <val>]  chip-select index (for external SPI)
                 default: 1
     [-m <val>]  SPI mode
     [-f <val>]  bus frequency in kHz
     [-q]        quiet startup (no message if no device found)
     [-T <val>]  Device type
                 values: 5607|5611, default: 5611

   stop

   status        print status info